Tips on Caring for the Right and the Right Printer

Just like old typewriters into life at work in our lives, especially in matters of administration and correspondence, today printerlah who became one of the capital in the works. But now, not just paperwork and correspondence that a lot depends on the printer, but it almost covers all areas - including for the type of graphic work. And whose name this printer, very rapid development. The first can only print to a maximum size of A3 +, now there's a printer that can print width of 4 meters, even labih, with unlimited length.

But that we will discuss here, just standard office printers and personal, that inkjet printers, which use only range to print documents and graphics in a maximum size of A3 +.

Tips on Caring for Caring BenarTips Printer That Printer That BenarKarena this printer can be very important, if more is needed for sure, so we hope that this stuff is always in top condition. Because if we again need to use but the printer was down, both in quality and technical, then woe to us. Therefore, technology object is not possible we can fix itself if damaged, except that only the disruption in terms of quality - for example, striped prints, or color is not flat, it can be overcome by performing mechanical repairs, which can be done with the help of software.

To avoid having problems when the printer we need, and also so that more durable printers, and print quality remains excellent, regular maintenance is necessary and painstaking. Well, here are tips that you can use to keep your printer longevity, relatively safe from the problem, and the results are always excellent.

How to care for the right printer:

Tips on Caring for Caring Printer Printer That BenarTips BenarYang The main thing is keeping the printer. Close all the way in and out of paper so that no objects in there. Both dust and other potentially damaging objects such as a clip or other object. Remove dust with a brush or blown, are for the wheels rubber or plastic, wipe with a damp cloth or a cotton bud soaked in, so that dust is lifted.

Because inkjet ink could freeze and obstruct the smooth ink when printing, the printer should be used every day, at least one sheet of paper.

When printing in large quantities, rest your printer after printing 15 pages each, about 5 minutes, so that no mechanical overheating causing premature wear.

Tips on Caring for Caring BenarTips Printer That Printer That BenarAgar paper is not sticky, so it retracts when printing in large quantities, before being put into the entry point of paper, the paper should be thoroughly shaken, that is by bend-bend (but not until it broke).

Do not put too much paper in the amount of the entry point into the paper, so as not to interfere with the mechanism of action wheel puller paper.

Use paper with a thickness of standard sizes or as recommended. Because not all printers can accept a paper that is too thick or too thin.

Each time a new turn on the printer, you should not directly be used. Allow the printer to warm up sufficiently, or if a new reset improperly discharged dead due to power failure and so on.

After use, turn off the printer through the habit of power. But before turning off, make sure the printer is completely in a state of the cartridge stops working and has returned to its original position.

Do the cleaning process if needed. For when too often make the process of cleaning, head cartridge will quickly wear out, so it will reduce print quality.

Tips on Caring for Caring BenarTips Printer That Printer That BenarMenggunakan original ink is the most appropriate choice, as long as you can bear with the price is not cheap. So, if want to print black and white documents, we recommend using the option to print only in black and white, not full color, because it will spend another color ink.

If you use the ink refill, you should do the refilling ink refilling place that is good quality. However, cartridge refilling has limits. So, if you've refilled a few times, usually cartridge performance will decrease, which means also reduces print quality.

If you use the ink infusion, you should not let the ink less than half of the tube.

Tips on Caring for Caring BenarTips Printer That Printer That BenarJika printer has a problem, you should not knowledgeably to fix it yourself. Therefore, the result is not so good but even more damaged. Because the printer is not every day is damaged, you should take it to the service or to where you put ink infusion, if the printer is having problems.

If the print is a daily routine, you should not have only one printer. So that if the printer has a problem, you still have a backup to be able to continue working.

Be careful with the printer parts that seem sensitive to dirt or touch, such as chips, sensors, and others. Because if it objects to the disorder, resulting in poor performance of the printer so.

Place the printer in a shady and dry place. Do not expose to direct sunlight and do not get hit too wet. Because the printer has many components that are susceptible to heat and wet.

Well, so be it. May be useful.

Read More..

What Will Happen If Notebook submerged in water?

If the notebook in a state of wet and dirty atmosphere flood affected, do not ever turn on (Power-on) let alone using electrical plugs. This situation will actually worsen Notebook. because it causes short-circuit on its

electronic components. Should immediately remove the cover to the place dry, discard all remaining atmosphere and the dirt path that linger with a clean cloth.

Next is to remove battere, then clean and mengeringkanya. If it looks dirty, clean with a soft cloth with a bit of atmosphere and rub gently. Beware of pole-pole plus-minus battere (usually of shiny yellow metal at the bottom / side of the body battere). Clean this section until dry. If it is dry you should not be installed battere back first to the Notebook.

Notebook basking under the sun, and put in a position to move inside the atmosphere could be right out. After dried in the sun until dry, can be sprayed with a hair dryer (hair dryer) to the inside of the cover can be reached. Spray dilubang others, such as speakers, port-connector, powe, keyboards and so on. Be careful not to position Hair-dryer too close so as not to damage the components.

Battere can also dijemu in the sun, but should be wrapped in a cloth first. Battere type of lithium (Li-Ion) are very sensitive to the thermal environment which can make its chemical structure is damaged and at risk of exploding. Should be dried to 1-3 hours. After itudapat inserted into the refrigerator (still wrapped in cloth), and do not memaskan into frezeer. Cold temperatures for several hours can restore the ability battere.

If you are familiar with the technical stuff, we can open cassis (body) cover to remove the main device (such as Processor, Hard Disk, Motherboard, RAM, etc.) to ensure everything is not damaged. Aritektur cover has a fairly simple system, composed of various modules are connected using labeling and cable connectors. To remember, because the components are usually small and delicate cover, an extra treatment needed careful.

Prepare toolset such as plus-minus screwdriver small and medium-sized, better if it has Ampere Meter. Turn the notebook, and all the nuts off the bottom so that the framework can be open (usually HDD, RAM Optical Drive located at the bottom). Memorize the location of the nut so that at the time of re-Symbian installation is not misplaced. Search carefully all the bolts are not yet open, and separate all the components that have been opened.

Notice all the existing cables and connectors. Do not get lost or damaged. Inijuga including existing circuit contained in the motherboard that should not be scratched or scuffed.

Components that pale susceptible to damage is a mechanical device such as Hard Disk and Optical Disc (CD / DVD), If you are able to open a second device, directly separate and dry the same as the above step.

Go all out off the cover and the maximum component that can be done. Separate all the equipment, then dry in the sun again until dry and occasionally sprayed with a hair-dryer. Once everything is dry measuring all components with Ampere Meter by connecting the connector to the device. If the number is still good is indicated, it means that components can be reused. Do not forget to do a contrast against battere well.

Replace all components carefully to positions semuladibagian on the notebook. Tighten all bautlalu spray after returning with a hair-dryer to make sure everything has dried, attach the original place battere.

We recommend using electricity to make the first contrast

, assuming battere have experienced the power vacuum. Do not immediately turned on, let battere absorb electrical energy for about an hour.

After that dislodged the power cord, then turn on as usual. If the cover display as usual, go into the BIOS menu by pressing the DEL or F12 (depending on the type of notebook). Check all information is correct BIOS tools, and do the necessary environment such as date, boot priority, and so on. If you do not understand, can do strange environment like its original condition when purchased. This option is certainly available dimenu BIOS.

If the cover does not turn on properly, it means that there are components that suffered severe damage. None other than pailihan replace them with new ones. We can call the businessman / play a lot of cover available. We can only hope that the damage is not too much and on key components such as processors and motherboards are worth quite expensive.

To avoid damaging the notebook, pale good attitude is to take some remedial action, namely menyelamatkanya before it flooded. But tragedy sometimes just happen and we need to take certain steps so that losses are not too large. It required extra activity as described above. Good luck, Good Luck

Read More..